Shopping cart

Filters

Personal menu

Preferences

Picture of Centrifugal Upblast Exhaust Fan, Model CUBE-180HP, Belt Drive, 1/2HP, 115/208-230V, 1Ph, Motor & Drives Unassembled, 1661-2587 CFM

Centrifugal Upblast Exhaust Fan, Model CUBE-180HP, Belt Drive, 1/2HP, 115/208-230V, 1Ph, Motor & Drives Unassembled, 1661-2587 CFM

$2,515.00

The CUBE is an aluminum exhaust fan specifically designed for roof or sidewall mounted applications where contaminated or grease laden exhaust air can be discharged directly upward, away from the roof or wall surface. The fans feature a one piece windband continuously welded to curb cap and double studded isolators for true vibration isolation.

30 x 30 inch base with prepunched mounting holes for easy attachment to roof curb
26.5 x 26.5 inch recommended roof opening
Roof or wall mountable

SKU: CUBE-180HP-5130GQD-DR1

Ships From: Greenheck

Qty:

View Related Products

Available In: 5-7 Business Days

Product Specifications
Performance
Dimensional Drawing
Literature
Certifications

Motor HP	Max BHP	Max Fan RPM	Min Fan RPM	Ps (in. wg)	0	0.125	0.25	0.375	0.5	0.625	0.75
1/2	0.34	920	830	CFM	2587	2476	2358	2228	2086	1899	1661
Sones	11.9	11.9	11.4	10.9	10.7	10.4	9.8
Bhp	0.27	0.29	0.31	0.32	0.34	0.34	0.34

Dimension
A	30 in
B	35.375 in
C	28.625 in

Dimensions
Base/Panel Length X Width Square base dimension on power roof ventilators. Square fan panel dimension on sidewall propeller fans.	30 x 30 in
Curb Cap Size Square base dimension on power roof ventilators.Tells you what size roof curb is needed.	30 in
Impeller Diameter Dimension of the impeller (propeller or wheel) in inches.	19 in
Roof Opening Width x Roof Opening Length Describes the size (width x lenght) of the roof opening that is required in order to properly install a given fan or ventilator.	26 1/2 x 26 1/2 in
Base Height Height of the curb cap on power roof ventilators.	1 3/4 in
Damper Width x Damper Height The "ACTUAL" damper width and height. Dampers are undersized to allow them to be mounted into the duct work/wall opening.	24 x 24 in
Bearing Size Bore size on the bearings utilized on a ventilator.	1 in
Height The height of a given product.	28 5/8 in
Weight Weight	98 lbs
Overall Diameter Describes the diameter at the widest point for a given product.	35 3/8 in

Performance
CFM Range CFM Range	1661-2587
FRPM Range FRPM Range	830-920

Application
Application Applications/uses for a particular fan or ventilator.	Exhaust General and Clean Air Exhaust Grease-Laden Air Exhaust General and Clean Air Exhaust Grease-Laden Air
Mounting Location Refers to the location where a fan or ventilator can be mounted.	Roof Wall Roof Wall

Construction Features
Drive Type Transmission type of the ventilator (belt drive or direct drive).	Belt Drive
Impeller Type Style of impeller that is utilized on a product (i.e. Centrifugal or Axial).	Centrifugal Wheel
Impeller Material Type of material the impeller of a fan or ventilator is constructed of.	Aluminum
Housing Material Type of material the housing of a ventilator is constructed of.	Spun Aluminum
Includes Describes items that a particular product includes such as mounting hardware, etc.	Unassembled drive package
Max Inlet Temp The maximum entering air temperature that a fan or ventilator can withstand while in operation, without compromising the life of the unit.	400 °F
Certifications Certifications	AMCA Sound & Air UL/cUL 705 Listed - Supplement SC - "Power Ventilators for Restaurant Exh. Appliances" (Formerly UL 762) AMCA Sound & Air UL/cUL 705 Listed - Supplement SC - "Power Ventilators for Restaurant Exh. Appliances" (Formerly UL 762)
Drive Package Description Describes whether the drive package on a particular ventilator is assembled, shipped loose, or must be provided by the customer.	Motor and drives shipped loose
Required Accessory Describes what accessory(s) must be purchased in addition to make the product fully functional.	Roof curb for new roof installations

Motor Information
Service Factor A safety factor to be used when the load temporarily exceeds the nominal horse power rating of a given motor. When used on a motor nameplate, a number which indicates how much above the nameplate rating a motor can be loaded without causing serious degrad	1.15
Phase Indicates the space relationships of windings and changing values of the recurring cycles of AC voltages and currents. The most common power supplies are either single- or three-phase.	1
Voltage The force that causes a current to flow in an electrical circuit. The voltage of a motor is usually determined by the supply to which it is attached. NEMA requires that motor be able to carry its rated horsepower at nameplate voltage plus or minus 1% al	115/208-230
HP The power required to drive an air moving device. Horsepower required varies with system conditions.	1/2
Hertz Measure of the frequency or cycles per second.	60
Motor Enclosure The housing or frame of the motor.	Open Drip Proof
RPM The number of times per minute the shaft of the motor (machine) rotates. This is a function of design and the power supply.	1800
Motor Insulation The class of motor insulation for a given motor. The temperature capabilities of each insulation class is defined as being the maximum temperature at which the insulation can be operated to yield an average life of 2, hours (A = 15?C, B = 135?C, F =	B
Thermal Protection This is a feature which protects the motor from overheating and thus prolongs service life of the machine. In the event that the motor approaches overheating the thermal protection cuts power and only returns it after a cooling period.	AutoOverload
Nominal Efficiency Nominal Efficiency	67.9
NEMA Frame Size Refers to a set of physical dimensions of motors as established by NEMA (National Electrical Manufacturers Association). These dimensions include critical mounting dimensions.	48

General
Unit of Measure Unit of Measure	ea
Warranty Length Warranty Length	1 Year

Model CUBE is an aluminum exhaust fan specifically designed for roof or sidewall mounted applications where contaminated or grease laden exhaust air can be discharged directly upward, away from the roof or wall surface. The fans feature a one piece windband continuously welded to curb cap and double studded isolators for true vibration isolation. Ideal for new installations or for retrofit, replacement applications. Curb adapters and reducers available to eliminate the need to field fabricate transitions when there is an existing roof curb.

Centrifugal wheel provides high-efficiency and minimal sound
One-piece aluminum windband with rolled bead provides extra rigidity
Cooling fins located on top of fan wheel draw outside air through a large breather tube directly into the motor compartment extending motor life
Windband is continually welded to the curb cap and drain trough for leakproof construction
Machine cast pulleys are adjustable for final system balancing
Permanent embossed aluminum nameplate for exact model and serial number identification
Motor, belt and pulleys shipped loose for field assembly

Products specifications

Unit of Measure	ea
Service Factor	1.15
Application	Exhaust General and Clean Air, Exhaust Grease-Laden Air
Mounting Location	Roof, Wall
Base/Panel Length X Width	30 x 30 in
Drive Type	Belt Drive
Phase	1
Voltage	115/208-230
HP	1/2
Impeller Type	Centrifugal Wheel
Impeller Material	Aluminum
Housing Material	Spun Aluminum
Includes	Unassembled drive package
Max Inlet Temp
Certifications	AMCA Sound & Air, UL/cUL 705 Listed - Supplement SC - "Power Ventilators for Restaurant Exh. Appliances" (Formerly UL 762)
Warranty Length	1 Year
Drive Package Description	Motor and drives shipped loose
Required Accessory	Roof curb for new roof installations
Curb Cap Size
Impeller Diameter
Roof Opening Width x Roof Opening Length
Base Height
Damper Width x Damper Height	24 x 24 in
Bearing Size
Height
Weight
Overall Diameter
Hertz
Motor Enclosure	Open Drip Proof
RPM
Motor Insulation	B
Thermal Protection	AutoOverload
Nominal Efficiency
NEMA Frame Size	48
CFM Range	1661-2587
FRPM Range	830-920

Motor HP	Horsepower. Used to indicate a fan's motor size.
Max BHP	Brake Horsepower. A measure of power consumption. Used to determine the proper motor horsepower and wiring.
Max Fan RPM	Revolutions Per Minute. Measure of maximum fan speed.
Min Fan RPM	Revolutions Per Minute. Measure of minimum fan speed.
Ps	Static Pressure. Resistance to airflow measured in inches of water gauge.
CFM	Cubic Feet Per Minute. A measure of airflow.
Sones	A measure of loudness. One sone can be approximated as the loudness of a quiet refrigerator at a distance of 5 feet. Sones follow a linear scale, that is, 10 sones are twice as loud as 5 sones.